AKF392 industrial using MEMS triaixal accelerometer Oil drilling Vibration Sensor
▶ APPLICATION
★ Medical equipment
★ Bridge
★ Automobile
★ Road roller
★ Wind power generation
★ Large machinery, engines
★ Low-frequency vibration and automatic monitoring
★ Traffic system monitoring, roadbed analysis and high-speed railway fault detection
This acceleration series can be applied to various fields such as vibration testing and impact testing.The product adopts digital interface output, RS232/485/TTL optional, different address codes can be set, and multiple sensors can be used in series for long distances, which is convenient for multi-point measurement and data analysis. The AKF392B is a monocrystal line silicon capacitive sensor, consisting of a micromachined silicon chip,a low-power ASIC for signal conditioning,a microprocessor for storing compensation values and a temperature sensor. This product has low power consumption, Complete calibration system, solid structure and stable output.The new electronic configuration provides solid-state power for reset, and providing full protection for over-current.In the full range,Typical values for long-term stability and bias of the scale factor are less than 0.1%. This series of products has the characteristics of strong structure, low power consumption and excellent deviation stability, which guarantees outstanding output reliability
Specifications
| AKG392 | PARAMETERS | UNIT |
| Range | ±2 | ±4 | ±8 | ±10 | ±20 | ±40 | g |
| Bias calibration | <1 | <1 | <1 | <1 | <1 | <1 | mg |
| Measure axis | X,Y,Z | X,Y,Z | X,Y,Z | X,Y,Z | X,Y,Z | X,Y,Z | axis |
| Power on/off repeatability | <2 | <2 | <2 | <2 | <2 | <2 | mg(max) |
| Bias temperature coefficient | 0.15 | 0.15 | 0.15 | 0.75 | 0.75 | 0.75 | %/℃(typical) |
| Resolution/threshold (@ 1Hz) | < 1 | < 1 | < 1 | < 1 | < 1 | < 1 | mg(max) |
| Non-linearity | <0.5 | <0.8 | <1 | <1 | <1 | <1 | % FS(max) |
| Bandwidth (3DB) | 500 | 500 | 500 | 500 | 500 | 500 | Hz |
| Cross axis sensitivity | 1 | 1 | 1 | 2 | 2 | 2 | % |
| Transverse vibration sensitivity ratio | 1 | 1 | 2 | 5 | 5 | 5 | % |
| Resonance frequency | 2.4 | 2.4 | 2.4 | 5.5 | 5.5 | 5.5 | kHz |
| Output rate | 5Hz,10Hz,25Hz,50Hz,100Hz,200Hz,500Hz,1000Hz |
| Output Interface | RS232/RS485/TTL |
| Protocol | RION 68 protocol and MODBUS RTU protocol |
| Reliability | MIL-HDBK-217,Grade 2 |
| Impact resistance | 100g@11ms, 3 Axial Direction (Half Sinusoid) |
| Recovery Time | <1ms(1000g, 1/2 sin 1ms, Impact on the i-axis) |
| Vibration | 20g rms,20~2000Hz (Random noise, o, p, i acts on each axis for 30 minutes) |
| Input(VDD_VSS) | 9~36 VDC |
| Operating current consumption | <60mA @ 12 VDC |
| Connector | Industry standard M12 connector |
| Weight | Product net weight: 82g, Magnetic base: 48g, L-shaped adapter plate 20g |
| Size | Product size: 34.3*34.3*38.5mm Magnetic adsorption base size: 34.23*34.23*6mm L-shaped adapter plate size: 36*44*15mm |
▶ COMMUNICATION PROTOCOL
The product includes 68 protocol and MODBUS RTU two protocols. The default configuration parameters of the protocol are as follows:
| PROTOCOL | RION 68 PROTOCOL | MODBUS-RTU |
| Address code | 0 | 1 |
| Broadcast address | 255 | 0 |
| Serial port baud rate | 9600 | 9600 |
| Parity bit | No parity | Even parity |
| Serial port start bit | 1 bit | 1 bit |
| Serial port data length | 8 bits | 8 bits |
| Serial port stop bit | 1 bit | 1 bit |
| Output mode | Question and answer | Question and answer |
| Data Format | Data format | Data format |
| Data check method | Checksum | CRC16 |
Size
Product Tags:
|
|
AKF392 industrial using MEMS triaixal accelerometer Oil drilling Vibration Sensor Images
|
